Float level gauge points of use

Float level gauge is widely used in liquid level, chemical industry, metallurgy, electric power, paper making, food and industrial sewage treatment and other departments. By the magnetic reed switch, precision resistors and amplification transform circuit. When the magnetic level gauge magnetic float to a certain position of the reed switch, the reed switch is closed, so that the amplifier output conversion circuit with the measured level corresponding to the current value, as the level changes, Amplifier conversion circuit level will be converted into a linear 4 ~ 20mADC signal output, in order to achieve the level of signal transmission or control.

Float level gauge use points:

1, the level gauge calibration is normal, cast and found the float in a certain position for a period of time "sucking" phenomenon. This is mainly the level gauge through the steel platform device, the gap between the plate and produced. Therefore, special attention should be paid to the clearance between the liquid level gauge pipe wall and the cutting edge of the platform through the steel platform device. Based on field experience, this distance is about 100 mm to ensure that no impact on the magnetic float.

2, on-site adjustment will find the float moving up and down not sensitive enough. This is mostly due to improper liquid level gauge caused by the device, this time to pay attention to the center of the flange can be up and down in a line, with the degree of vertical plane. Generally speaking, the best angle with the degree of not less than 87 degrees, if the bias is greater, may affect the smooth movement of the float.

3, when the level gauge cast on the spot, pay special attention to open the upper gate valve, then open the lower gate valve. This is due to the level gauge connected to the bottom of the tube is equipped with a maintenance of the float spring, otherwise, the role of large differential pressure float may cause the float gauge can not be used.

4, the use of liquid level gauge, if the output signal generated frequent disturbance or interference pulse, it is necessary to check the signal cable shield can be firmly grounded, the work of the resistance can meet the request. If the interference is still not completely eliminated, available signal isolator to deal with.

5, the level gauge put into use for a period of time, showing floats difficult to float and the float moving insensitive situation. This is fundamentally due to the presence of iron filings or other contaminants on the magnetic float. You can empty the media, and then remove the float, remove the magnetic float stained with iron or other dirt can be.

6, if for transport or other reasons led to the scene instructions for the closed glass tube rupture, you can use domestic glass tube change. But it is best to take a vacuum. Also pay attention to the vertical glass tube, so as not to affect the indicator of the instructions.

7, special attention to the use of level gauge, do not use a strong magnet in the connected tube up and down to stop the float up and down, otherwise it will lead to changes in the polarity of the magnetic float magnetization, and even make the float magnetic weakened, resulting in difficult to work properly.

BRIEF INTRODUCTION

Henan Yuteng Grinding Material Co., Ltd. is located in Kaifeng City, Henan Province. Is a set of production, research and development, service as one of the grinding agent, grinding, polishing products professional company, specializing in the production and sales of coated grinding tools derived ancillary products: flocking sand disc, blade, all kinds of special-shaped grinding disc, sponge grinding block, steel paper disk, ring sand belt, sand ring and automotive polishing products.

Our main products are Velcro Disc,Abrasive Paper,Fiber Disc,Flap Disc,Abrasive Cloth,Abrasive Belt.

Relying on the advantages of the industrial base, the company has advanced production equipment and strong technical force, complete testing equipment to ensure that the products are sharp, wear-resistant and high strength, and the product quality reaches the advanced level of similar international products.

Our products can be used for all kinds of metal watches and stainless steel, alloy steel, non-alloy steel, non-ferrous metals, titanium alloy and other grinding and wire drawing, polishing and so on; Wood, high-medium fiberboard, flower board, composite board, glass, rubber and other table grinding and polishing. Widely used in automobile, steel, building materials, shipping, aviation, wood, plastic, leather and other industries.

We provide customers with the best surface treatment program, according to the actual needs of customers "tailored" a variety of specifications of sand pan, sand belt, sand carbon and emery cloth ring polishing products.

The company's flexible operating mechanism and all customer-centric concept, we in addition to provide you  standardized, serialized products, but also according to your special requirements, for you to manufacture high-quality, personalized non-standard coated with abrasive products.